Salem All,
J'ai besoin d'aide, ma dreambox 800HD PVR originale, ne veut plus fonctionner du jour au lendemain alors je n'ai pas touché au soft/image depuis plus d'1 an. Un jour je l'allume et elle se bloque sur /flash/vmlinux.gz.
J'ai tenté alors de la flasher avev differentes images et toujours le meme résultat, l'image se charge sur la box et lors du démarage se bloque !!! Pour info, j'ai effectué le flashage via http et RS232 même résultat :-(
Voici le débug, si quelqu'un pouvait m'aider, par avance merci :
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800
FIRST STAGE 1.01(0x133/high) {BO23456}
2ND STAGE OK, build #84 (2011-09-02)
0.000 - BCM board setup
0.002 - fp init
0.003 - ca init
0.893 - load config
0.921 - config loaded.
* press to enter setup
0.926 - ide init
OLED found!
lcd: BOOT #84
1.250 - main control
Initializing USB.
USB: Locating Class 09 Vendor 0000 Product 0000:
USB Hub
- read config file: /boot/secondstage.conf
1.294 - load /boot/secondstage.conf to 833000c0 (max=65535)
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
++++++++++++++++++UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
2.441 - jffs2 size: 2304 kb
2.443 - network: 2.445 manual, ip address is 192.168.0.38
2.486 - starting network
2.492 - httpd, telnetd, dreamupd
dreamupd initialized
2.497 - ok. start receiving packets
2.501 - using jffs2
Scanning JFFS2 FS: . done.
find_inode failed for name=secondstage.conf
load: Failed to find inode
2.635 - size: 0
- failed to open /boot/secondstage.conf
2.640 - not entering setup
2.643 - execute script: /cf/autorun.bat
2.646 - load /cf/autorun.bat to 833000c0 (max=65535)
2.651 - size: -1
- failed to open /cf/autorun.bat
2.656 - force boot: -1
2.658 - try boot from 1:
2.660 - execute script: /boot/autoexec.bat
2.664 - load /boot/autoexec.bat to 833000c0 (max=65535)
2.669 - using jffs2
2.672 - size: 38
lcd: /flash/bootlogo.elf
2.678 - load /flash/bootlogo.elf to 82000000 (max=16777216)
2.684 - using jffs2
2.710 - size: 159445
2.712 - decompressing elf (compressed: 159445 bytes)
2.782 - decompression ok (uncompressed: 403100 bytes)
2.786 - loading elf image at 88000000
2.947 - jumping to 8043daa0
2.950 - load /boot/bootlogo.jpg to a2800000 (max=1048576)
2.955 - using jffs2
3.006 - size: 285065
bootlogo size: 285065
no HDMI device detected
no HDMI mode available, reverting to 720p
using 1280x720p (60.00 Hz)
HDMI
using colorspace: 0
create surface 1280 720
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <[email protected]>
parsing JPEG header..
Virtual FB Size: 1280x720
lcd: /flash/vmlinux.gz
4.046 - load /flash/vmlinux.gz to 82000000 (max=16777216)
4.051 - using jffs2
4.281 - size: 1856548
4.283 - decompressing elf (compressed: 1856548 bytes)
5.037 - decompression ok (uncompressed: 4228892 bytes)
5.042 - loading elf image at 88000000
5.539 * Quiesce...
5.541 *** Turning off USB
USB: Unregistering Hub VID 0x0000 PID 0x0000
USB: Powering down bus 0 port 2
USB: Powering down bus 0 port 1
5.553 *** Quiesce network...
5.556 - jumping to 8033c000
<5>Linux version 2.6.18-7.4-dm800 (ghost@rabbit) (gcc version 4.4.3 (GCC) ) #1 Tue Mar 27 12:15:44 UTC 2012
Fetching vars from bootloader... none present, using defaults.
board_init_once: regval=44ac6502, ddr_strap=3, 4 chips, pci_size=2
Detected 256 MB on board
<4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824
Default command line =
root=/dev/mtdblock3 rootfstype=jffs2 rw console=null
2 831ffebc 83029b34
g_board_RAM_size=256MB
Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=0
CPU revision is: 00020000
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
---> memsize from bootloader: 148
User-defined physical RAM map:
node [00000000, 09400000: RAM]
node [09400000, 06c00000: RSVD]
<5>Reserving 108 MB upper memory starting at 09400000
<7>On node 0 totalpages: 65536
<7> DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists. Total pages: 65536
<5>Kernel command line: console=ttyS0,115200 ip=10.0.120.203 nfsroot=10.0.120.77:/home/tmbinc/target/mips root=/dev/nfs rw
before init RAC 0x02a00000 0x00000000
after init RAC 0x02a0000f 0x0fff0000
[4294667.296000] Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
[4294667.296000] Primary data cache 32kB, 2-way, linesize 16 bytes.
[4294667.296000] Synthesized TLB refill handler (20 instructions).
[4294667.296000] Synthesized TLB load handler fastpath (32 instructions).
[4294667.296000] Synthesized TLB store handler fastpath (32 instructions).
[4294667.296000] Synthesized TLB modify handler fastpath (31 instructions).
[4294667.296000] timer irq 67 end 57
[4294667.296000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[4294667.296000] Found MIPS counter frequency: 149 Mhz
[4294667.296000] Using 148.501 MHz high precision timer.
[4294667.296000] Console: colour dummy device 80x25
[4294667.296000] ################## brcm_serial_console_init, sercon=80307da0
[4294667.369000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[4294667.378000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[4294667.412000] Memory: 145536k/262144k available (2703k kernel code, 116436k reserved, 601k data, 128k init, 0k highmem)
[4294667.446000] Mount-cache hash table entries: 512
[4294667.451000] Checking for 'wait' instruction... available.
[4294667.461000] NET: Registered protocol family 16
[4294667.467000] registering PCI controller with io_map_base unset
[4294667.473000] registering PCI controller with io_map_base unset
[4294667.481000] SCSI subsystem initialized
[4294667.485000] usbcore: registered new driver usbfs
[4294667.490000] usbcore: registered new driver hub
[4294667.496000] SATA: Primary Bus Master Status Register offset = b0520000 + 00000300 = b0520300
[4294667.505000] SATA: before init Primary Bus Master Status reg = 0x00000000.
[4294667.512000] SATA: after init Primary Bus Master Status reg = 0x00000020.
[4294667.521000] NET: Registered protocol family 2
[4294667.535000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[4294667.543000] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[4294667.551000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[4294667.558000] TCP: Hash tables configured (established 8192 bind 4096)
[4294667.565000] TCP reno registered
[4294667.573000] JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
[4294667.580000] Initializing Cryptographic API
[4294667.585000] io scheduler noop registered
[4294667.589000] io scheduler anticipatory registered (default)
[4294667.595000] io scheduler deadline registered
[4294667.599000] io scheduler cfq registered
[4294667.613000] Broadcom serial driver version 1.00 (2000-11-09) with SERIAL_PCI enabled
[4294667.638000] loop: loaded (max 8 devices)
[4294667.642000] Broadcom BCM7401 P31 Ethernet Network Device v2.0 Mar 27 2012 12:14:26
[4294667.650000] SUNDRY revision = 74010021, have IP Hdr Opt=1
[4294667.663000] Config Internal PHY Through MDIO: Auto-negotiation timed-out
[4294669.757000] : 10 MB Half-Duplex (assumed)
[4294669.767000] ata1: SATA max UDMA/133 cmd 0xB0510000 ctl 0xB0510020 bmdma 0xB0510030 irq 42
[4294669.776000] scsi0 : sata_svw
[4294670.086000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F0000)
[4294670.095000] ata1.00: ATA-8, max UDMA7, 234441648 sectors: LBA48 NCQ (depth 0/32)
[4294670.106000] ata1.00: configured for UDMA/133
[4294670.111000] Vendor: ATA Model: SAMSUNG HM121HI Rev: LZ10
[4294670.118000] Type: Direct-Access ANSI SCSI revision: 05
[4294670.126000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
[4294670.134000] sda: Write Protect is off
[4294670.138000] SCSI device sda: drive cache: write back
[4294670.144000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
[4294670.151000] sda: Write Protect is off
[4294670.155000] SCSI device sda: drive cache: write back
[4294670.160000] sda: sda1
[4294670.725000] sd 0:0:0:0: Attached scsi disk sda
[4294670.730000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[4294670.737000] Broadcom STB NAND controller (BrcmNand Controller)
[4294670.743000] B4: NandSelect=40000002, nandConfig=04042300, chipSelect=1
[4294670.750000] brcmnand_probe: CS1: dev_id=ad76ad76
[4294670.755000] After: NandSelect=40000002, nandConfig=04042300
[4294670.761000] NAND Config: Reg=04042300, chipSize=64 MB, blockSize=16K, erase_shift=e
[4294670.769000] busWidth=1, pageSize=512B, page_shift=9, page_mask=000001ff
[4294670.776000] timing1 not adjusted: 5363444f
[4294670.780000] timing2 not adjusted: 00000fc6
[4294670.784000] BrcmNAND mfg ad 76 Hynix HY27US08121A (dream) 64MB
[4294670.791000]
[4294670.791000] Found NAND: ACC=e3000000, cfg=04042300, flashId=ad76ad76, tim1=5363444f, tim2=00000fc6
[4294670.802000] BrcmNAND version = 0x0001 64MB @00000000
[4294670.807000] Found NAND chip on Chip Select 1, chipSize=64MB, usable size=64MB, base=14000000
[4294670.816000] ACC_CONTROL B4: e3000000
[4294670.820000] page_shift=9, bbt_erase_shift=14, chip_shift=26, phys_erase_shift=14
[4294670.827000] Brcm NAND controller version = 0.1 NAND flash size 64MB @14000000
[4294670.835000] mtd->oobsize=16, mtd->eccOobSize=16
[4294670.840000] brcmnand_scan: mtd->oobsize=16
[4294670.844000] brcmnand_scan: oobavail=12, eccsize=512, writesize=512
[4294670.850000] brcmnand_scan, eccsize=512, writesize=512, eccsteps=1, ecclevel=15, eccbytes=3
[4294670.859000] brcmnand_default_bbt: bbt_td = bbt_main_descr
[4294670.866000] brcmnandCET: Status -> Deferred
[4294670.871000] numchips=1, size=4000000
[4294670.875000] Creating 4 MTD partitions on "bcm7xxx-nand.0":
[4294670.881000] 0x0000000000000000-0x0000000004000000 : "complete"
[4294670.890000] 0x0000000000000000-0x0000000000040000 : "loader"
[4294670.897000] 0x0000000000040000-0x0000000000400000 : "boot partition"
[4294670.904000] 0x0000000000400000-0x0000000004000000 : "root partition"
[4294670.914000] ehci_hcd_brcm_init: Initializing 1 EHCI controller(s)
[4294670.921000] 10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-0)
[4294670.929000] drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
[4294670.937000] - USB h/w setup mode <B>
[4294670.937000] - USB power enable set for active LOW mode
[4294670.946000] brcm-ehci brcm-ehci.0: BRCM EHCI
[4294670.951000] brcm-ehci brcm-ehci.0: new USB bus registered, assigned bus number 1
[4294670.959000] brcm-ehci brcm-ehci.0: irq 62, io mem 0x10480300
[4294670.965000] brcm-ehci brcm-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
[4294670.974000] usb usb1: configuration #1 chosen from 1 choice
[4294670.980000] hub 1-0:1.0: USB hub found
[4294670.984000] hub 1-0:1.0: 2 ports detected
[4294671.090000] ohci_hcd_brcm_init: Initializing 2 OHCI controller(s)
[4294671.097000] 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-0)
[4294671.105000] drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
[4294671.112000] - Resetting at b0480408
[4294671.116000] <-- brcm_start_hc
[4294671.119000] brcm-ohci-0 brcm-ohci-0.0: BRCM OHCI
[4294671.124000] brcm-ohci-0 brcm-ohci-0.0: new USB bus registered, assigned bus number 2
[4294671.133000] brcm-ohci-0 brcm-ohci-0.0: irq 63, io mem 0x10480400
[4294671.194000] usb usb2: configuration #1 chosen from 1 choice
[4294671.200000] hub 2-0:1.0: USB hub found
[4294671.205000] hub 2-0:1.0: 2 ports detected
[4294671.310000] 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-1)
[4294671.319000] drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
[4294671.326000] - Resetting at b0480508
[4294671.330000] <-- brcm_start_hc
[4294671.333000] brcm-ohci-1 brcm-ohci-1.1: BRCM OHCI
[4294671.338000] brcm-ohci-1 brcm-ohci-1.1: new USB bus registered, assigned bus number 3
[4294671.346000] brcm-ohci-1 brcm-ohci-1.1: irq 64, io mem 0x10480500
[4294671.408000] usb usb3: configuration #1 chosen from 1 choice
[4294671.414000] hub 3-0:1.0: USB hub found
[4294671.418000] hub 3-0:1.0: 2 ports detected
[4294671.524000] Initializing USB Mass Storage driver...
[4294671.530000] usbcore: registered new driver usb-storage
[4294671.535000] USB Mass Storage support registered.
[4294671.540000] i2c /dev entries driver
[4294671.544000] Advanced Linux Sound Architecture Driver Version 1.0.12rc1 (Thu Jun 22 13:55:50 2006 UTC).
[4294671.554000] ALSA device list:
[4294671.557000] No soundcards found.
[4294671.561000] TCP bic registered
[4294671.565000] NET: Registered protocol family 1
[4294671.569000] NET: Registered protocol family 17
[4294673.077000] IP-Config: Guessing netmask 255.0.0.0
[4294673.083000] IP-Config: Complete:
[4294673.086000] device=eth0, addr=10.0.120.203, mask=255.0.0.0, gw=255.255.255.255,
[4294673.094000] host=10.0.120.203, domain=, nis-domain=(none),
[4294673.100000] bootserver=255.255.255.255, rootserver=10.0.120.77, rootpath=
[4294673.109000] Looking up port of RPC 100003/2 on 10.0.120.77
[4294708.115000] portmap: server 10.0.120.77 not responding, timed out
[4294708.121000] Root-NFS: Unable to get nfsd port number from server, using default
[4294708.129000] Looking up port of RPC 100005/1 on 10.0.120.77
[4294743.135000] portmap: server 10.0.120.77 not responding, timed out
[4294743.141000] Root-NFS: Unable to get mountd port number from server, using default
[4294778.149000] mount: server 10.0.120.77 not responding, timed out
[4294778.155000] Root-NFS: Server returned error -5 while mounting /home/tmbinc/target/mips
[4294778.163000] VFS: Unable to mount root fs via NFS, trying floppy.
[4294778.171000] VFS: Cannot open root device "nfs" or unknown-block(2,0)
[4294778.178000] Please append a correct "root=" boot option
[4294778.183000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)
[4294778.192000] <0>Rebooting in 180 seconds..
J'ai besoin d'aide, ma dreambox 800HD PVR originale, ne veut plus fonctionner du jour au lendemain alors je n'ai pas touché au soft/image depuis plus d'1 an. Un jour je l'allume et elle se bloque sur /flash/vmlinux.gz.
J'ai tenté alors de la flasher avev differentes images et toujours le meme résultat, l'image se charge sur la box et lors du démarage se bloque !!! Pour info, j'ai effectué le flashage via http et RS232 même résultat :-(
Voici le débug, si quelqu'un pouvait m'aider, par avance merci :
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800
FIRST STAGE 1.01(0x133/high) {BO23456}
2ND STAGE OK, build #84 (2011-09-02)
0.000 - BCM board setup
0.002 - fp init
0.003 - ca init
0.893 - load config
0.921 - config loaded.
* press
0.926 - ide init
OLED found!
lcd: BOOT #84
1.250 - main control
Initializing USB.
USB: Locating Class 09 Vendor 0000 Product 0000:
USB Hub
- read config file: /boot/secondstage.conf
1.294 - load /boot/secondstage.conf to 833000c0 (max=65535)
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
++++++++++++++++++UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
2.441 - jffs2 size: 2304 kb
2.443 - network: 2.445 manual, ip address is 192.168.0.38
2.486 - starting network
2.492 - httpd, telnetd, dreamupd
dreamupd initialized
2.497 - ok. start receiving packets
2.501 - using jffs2
Scanning JFFS2 FS: . done.
find_inode failed for name=secondstage.conf
load: Failed to find inode
2.635 - size: 0
- failed to open /boot/secondstage.conf
2.640 - not entering setup
2.643 - execute script: /cf/autorun.bat
2.646 - load /cf/autorun.bat to 833000c0 (max=65535)
2.651 - size: -1
- failed to open /cf/autorun.bat
2.656 - force boot: -1
2.658 - try boot from 1:
2.660 - execute script: /boot/autoexec.bat
2.664 - load /boot/autoexec.bat to 833000c0 (max=65535)
2.669 - using jffs2
2.672 - size: 38
lcd: /flash/bootlogo.elf
2.678 - load /flash/bootlogo.elf to 82000000 (max=16777216)
2.684 - using jffs2
2.710 - size: 159445
2.712 - decompressing elf (compressed: 159445 bytes)
2.782 - decompression ok (uncompressed: 403100 bytes)
2.786 - loading elf image at 88000000
2.947 - jumping to 8043daa0
2.950 - load /boot/bootlogo.jpg to a2800000 (max=1048576)
2.955 - using jffs2
3.006 - size: 285065
bootlogo size: 285065
no HDMI device detected
no HDMI mode available, reverting to 720p
using 1280x720p (60.00 Hz)
HDMI
using colorspace: 0
create surface 1280 720
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <[email protected]>
parsing JPEG header..
Virtual FB Size: 1280x720
lcd: /flash/vmlinux.gz
4.046 - load /flash/vmlinux.gz to 82000000 (max=16777216)
4.051 - using jffs2
4.281 - size: 1856548
4.283 - decompressing elf (compressed: 1856548 bytes)
5.037 - decompression ok (uncompressed: 4228892 bytes)
5.042 - loading elf image at 88000000
5.539 * Quiesce...
5.541 *** Turning off USB
USB: Unregistering Hub VID 0x0000 PID 0x0000
USB: Powering down bus 0 port 2
USB: Powering down bus 0 port 1
5.553 *** Quiesce network...
5.556 - jumping to 8033c000
<5>Linux version 2.6.18-7.4-dm800 (ghost@rabbit) (gcc version 4.4.3 (GCC) ) #1 Tue Mar 27 12:15:44 UTC 2012
Fetching vars from bootloader... none present, using defaults.
board_init_once: regval=44ac6502, ddr_strap=3, 4 chips, pci_size=2
Detected 256 MB on board
<4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824
Default command line =
root=/dev/mtdblock3 rootfstype=jffs2 rw console=null
2 831ffebc 83029b34
g_board_RAM_size=256MB
Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=0
CPU revision is: 00020000
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
---> memsize from bootloader: 148
User-defined physical RAM map:
node [00000000, 09400000: RAM]
node [09400000, 06c00000: RSVD]
<5>Reserving 108 MB upper memory starting at 09400000
<7>On node 0 totalpages: 65536
<7> DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists. Total pages: 65536
<5>Kernel command line: console=ttyS0,115200 ip=10.0.120.203 nfsroot=10.0.120.77:/home/tmbinc/target/mips root=/dev/nfs rw
before init RAC 0x02a00000 0x00000000
after init RAC 0x02a0000f 0x0fff0000
[4294667.296000] Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
[4294667.296000] Primary data cache 32kB, 2-way, linesize 16 bytes.
[4294667.296000] Synthesized TLB refill handler (20 instructions).
[4294667.296000] Synthesized TLB load handler fastpath (32 instructions).
[4294667.296000] Synthesized TLB store handler fastpath (32 instructions).
[4294667.296000] Synthesized TLB modify handler fastpath (31 instructions).
[4294667.296000] timer irq 67 end 57
[4294667.296000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[4294667.296000] Found MIPS counter frequency: 149 Mhz
[4294667.296000] Using 148.501 MHz high precision timer.
[4294667.296000] Console: colour dummy device 80x25
[4294667.296000] ################## brcm_serial_console_init, sercon=80307da0
[4294667.369000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[4294667.378000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[4294667.412000] Memory: 145536k/262144k available (2703k kernel code, 116436k reserved, 601k data, 128k init, 0k highmem)
[4294667.446000] Mount-cache hash table entries: 512
[4294667.451000] Checking for 'wait' instruction... available.
[4294667.461000] NET: Registered protocol family 16
[4294667.467000] registering PCI controller with io_map_base unset
[4294667.473000] registering PCI controller with io_map_base unset
[4294667.481000] SCSI subsystem initialized
[4294667.485000] usbcore: registered new driver usbfs
[4294667.490000] usbcore: registered new driver hub
[4294667.496000] SATA: Primary Bus Master Status Register offset = b0520000 + 00000300 = b0520300
[4294667.505000] SATA: before init Primary Bus Master Status reg = 0x00000000.
[4294667.512000] SATA: after init Primary Bus Master Status reg = 0x00000020.
[4294667.521000] NET: Registered protocol family 2
[4294667.535000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[4294667.543000] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[4294667.551000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[4294667.558000] TCP: Hash tables configured (established 8192 bind 4096)
[4294667.565000] TCP reno registered
[4294667.573000] JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
[4294667.580000] Initializing Cryptographic API
[4294667.585000] io scheduler noop registered
[4294667.589000] io scheduler anticipatory registered (default)
[4294667.595000] io scheduler deadline registered
[4294667.599000] io scheduler cfq registered
[4294667.613000] Broadcom serial driver version 1.00 (2000-11-09) with SERIAL_PCI enabled
[4294667.638000] loop: loaded (max 8 devices)
[4294667.642000] Broadcom BCM7401 P31 Ethernet Network Device v2.0 Mar 27 2012 12:14:26
[4294667.650000] SUNDRY revision = 74010021, have IP Hdr Opt=1
[4294667.663000] Config Internal PHY Through MDIO: Auto-negotiation timed-out
[4294669.757000] : 10 MB Half-Duplex (assumed)
[4294669.767000] ata1: SATA max UDMA/133 cmd 0xB0510000 ctl 0xB0510020 bmdma 0xB0510030 irq 42
[4294669.776000] scsi0 : sata_svw
[4294670.086000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F0000)
[4294670.095000] ata1.00: ATA-8, max UDMA7, 234441648 sectors: LBA48 NCQ (depth 0/32)
[4294670.106000] ata1.00: configured for UDMA/133
[4294670.111000] Vendor: ATA Model: SAMSUNG HM121HI Rev: LZ10
[4294670.118000] Type: Direct-Access ANSI SCSI revision: 05
[4294670.126000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
[4294670.134000] sda: Write Protect is off
[4294670.138000] SCSI device sda: drive cache: write back
[4294670.144000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
[4294670.151000] sda: Write Protect is off
[4294670.155000] SCSI device sda: drive cache: write back
[4294670.160000] sda: sda1
[4294670.725000] sd 0:0:0:0: Attached scsi disk sda
[4294670.730000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[4294670.737000] Broadcom STB NAND controller (BrcmNand Controller)
[4294670.743000] B4: NandSelect=40000002, nandConfig=04042300, chipSelect=1
[4294670.750000] brcmnand_probe: CS1: dev_id=ad76ad76
[4294670.755000] After: NandSelect=40000002, nandConfig=04042300
[4294670.761000] NAND Config: Reg=04042300, chipSize=64 MB, blockSize=16K, erase_shift=e
[4294670.769000] busWidth=1, pageSize=512B, page_shift=9, page_mask=000001ff
[4294670.776000] timing1 not adjusted: 5363444f
[4294670.780000] timing2 not adjusted: 00000fc6
[4294670.784000] BrcmNAND mfg ad 76 Hynix HY27US08121A (dream) 64MB
[4294670.791000]
[4294670.791000] Found NAND: ACC=e3000000, cfg=04042300, flashId=ad76ad76, tim1=5363444f, tim2=00000fc6
[4294670.802000] BrcmNAND version = 0x0001 64MB @00000000
[4294670.807000] Found NAND chip on Chip Select 1, chipSize=64MB, usable size=64MB, base=14000000
[4294670.816000] ACC_CONTROL B4: e3000000
[4294670.820000] page_shift=9, bbt_erase_shift=14, chip_shift=26, phys_erase_shift=14
[4294670.827000] Brcm NAND controller version = 0.1 NAND flash size 64MB @14000000
[4294670.835000] mtd->oobsize=16, mtd->eccOobSize=16
[4294670.840000] brcmnand_scan: mtd->oobsize=16
[4294670.844000] brcmnand_scan: oobavail=12, eccsize=512, writesize=512
[4294670.850000] brcmnand_scan, eccsize=512, writesize=512, eccsteps=1, ecclevel=15, eccbytes=3
[4294670.859000] brcmnand_default_bbt: bbt_td = bbt_main_descr
[4294670.866000] brcmnandCET: Status -> Deferred
[4294670.871000] numchips=1, size=4000000
[4294670.875000] Creating 4 MTD partitions on "bcm7xxx-nand.0":
[4294670.881000] 0x0000000000000000-0x0000000004000000 : "complete"
[4294670.890000] 0x0000000000000000-0x0000000000040000 : "loader"
[4294670.897000] 0x0000000000040000-0x0000000000400000 : "boot partition"
[4294670.904000] 0x0000000000400000-0x0000000004000000 : "root partition"
[4294670.914000] ehci_hcd_brcm_init: Initializing 1 EHCI controller(s)
[4294670.921000] 10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-0)
[4294670.929000] drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
[4294670.937000] - USB h/w setup mode <B>
[4294670.937000] - USB power enable set for active LOW mode
[4294670.946000] brcm-ehci brcm-ehci.0: BRCM EHCI
[4294670.951000] brcm-ehci brcm-ehci.0: new USB bus registered, assigned bus number 1
[4294670.959000] brcm-ehci brcm-ehci.0: irq 62, io mem 0x10480300
[4294670.965000] brcm-ehci brcm-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
[4294670.974000] usb usb1: configuration #1 chosen from 1 choice
[4294670.980000] hub 1-0:1.0: USB hub found
[4294670.984000] hub 1-0:1.0: 2 ports detected
[4294671.090000] ohci_hcd_brcm_init: Initializing 2 OHCI controller(s)
[4294671.097000] 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-0)
[4294671.105000] drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
[4294671.112000] - Resetting at b0480408
[4294671.116000] <-- brcm_start_hc
[4294671.119000] brcm-ohci-0 brcm-ohci-0.0: BRCM OHCI
[4294671.124000] brcm-ohci-0 brcm-ohci-0.0: new USB bus registered, assigned bus number 2
[4294671.133000] brcm-ohci-0 brcm-ohci-0.0: irq 63, io mem 0x10480400
[4294671.194000] usb usb2: configuration #1 chosen from 1 choice
[4294671.200000] hub 2-0:1.0: USB hub found
[4294671.205000] hub 2-0:1.0: 2 ports detected
[4294671.310000] 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-1)
[4294671.319000] drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
[4294671.326000] - Resetting at b0480508
[4294671.330000] <-- brcm_start_hc
[4294671.333000] brcm-ohci-1 brcm-ohci-1.1: BRCM OHCI
[4294671.338000] brcm-ohci-1 brcm-ohci-1.1: new USB bus registered, assigned bus number 3
[4294671.346000] brcm-ohci-1 brcm-ohci-1.1: irq 64, io mem 0x10480500
[4294671.408000] usb usb3: configuration #1 chosen from 1 choice
[4294671.414000] hub 3-0:1.0: USB hub found
[4294671.418000] hub 3-0:1.0: 2 ports detected
[4294671.524000] Initializing USB Mass Storage driver...
[4294671.530000] usbcore: registered new driver usb-storage
[4294671.535000] USB Mass Storage support registered.
[4294671.540000] i2c /dev entries driver
[4294671.544000] Advanced Linux Sound Architecture Driver Version 1.0.12rc1 (Thu Jun 22 13:55:50 2006 UTC).
[4294671.554000] ALSA device list:
[4294671.557000] No soundcards found.
[4294671.561000] TCP bic registered
[4294671.565000] NET: Registered protocol family 1
[4294671.569000] NET: Registered protocol family 17
[4294673.077000] IP-Config: Guessing netmask 255.0.0.0
[4294673.083000] IP-Config: Complete:
[4294673.086000] device=eth0, addr=10.0.120.203, mask=255.0.0.0, gw=255.255.255.255,
[4294673.094000] host=10.0.120.203, domain=, nis-domain=(none),
[4294673.100000] bootserver=255.255.255.255, rootserver=10.0.120.77, rootpath=
[4294673.109000] Looking up port of RPC 100003/2 on 10.0.120.77
[4294708.115000] portmap: server 10.0.120.77 not responding, timed out
[4294708.121000] Root-NFS: Unable to get nfsd port number from server, using default
[4294708.129000] Looking up port of RPC 100005/1 on 10.0.120.77
[4294743.135000] portmap: server 10.0.120.77 not responding, timed out
[4294743.141000] Root-NFS: Unable to get mountd port number from server, using default
[4294778.149000] mount: server 10.0.120.77 not responding, timed out
[4294778.155000] Root-NFS: Server returned error -5 while mounting /home/tmbinc/target/mips
[4294778.163000] VFS: Unable to mount root fs via NFS, trying floppy.
[4294778.171000] VFS: Cannot open root device "nfs" or unknown-block(2,0)
[4294778.178000] Please append a correct "root=" boot option
[4294778.183000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)
[4294778.192000] <0>Rebooting in 180 seconds..