Voila les instructions que je reçois en COM1 avec Putty
Options: sata=0 enet=1 emac_1=0 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=0
CPU revision is: 0101954c
FPU revision is: 01739300
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
User-defined physical RAM map:
node [00000000, 07000000: RAM]
node [07000000, 09000000: RSVD]
<5>Reserving 144 MB upper memory starting at 07000000
<7>On node 0 totalpages: 65536
<7> DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists. Total pages: 65536
<5>Kernel command line: rootfstype=jffs2 root=/dev/mtdblock0 rw mem=0x8000000 c onsole=ttyS0,115200
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
MIPS secondary cache 128kB, 8-way, linesize 128 bytes.
SCM configuration: 00fac688 41d4d617 00f07100 8fff0d00 81ff0100 0fff0fff
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
timer irq 100
PID hash table entries: 2048 (order: 11, 8192 bytes)
Found MIPS counter frequency: 167 Mhz
Using 166.501 MHz high precision timer.
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 109184k/262144k available (2379k kernel code, 152848k reserved, 500k dat a, 120k init, 0k highmem)
Mount-cache hash table entries: 512
Checking for 'wait' instruction... available.
NET: Registered protocol family 16
PCI->SDRAM window size: 512MB
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
brcm-pm: disabling power to USB block
brcm-pm: disabling power to ENET block
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 22) is a 16550A
loop: loaded (max 8 devices)
brcm-pm: enabling power to ENET block
Broadcom BCM7325 P20 Ethernet Network Device v2.0 Sep 13 2011 00:00:01
Config Internal PHY Through MDIO: Auto-negotiation timed-out
: 10 MB Half-Duplex (assumed)
blackhole initialised
Broadcom STB NAND controller (BrcmNand Controller)
i=0, CS[0] = 0
NAND_CS_NAND_XOR=00000001
brcmnand_probe: CS0: dev_id=ecf10095
After: NandSelect=40000101, nandConfig=55042200
NAND Config: Reg=55042200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB
Found NAND: ACC=d3000000, cfg=55042200, flashId=ecf10095, tim1=4232222d, tim2=00 000d94
BrcmNAND version = 0x0200 128MB @00000000
brcmnand_probe: CS0: dev_id=ecf10095
After: NandSelect=40000101, nandConfig=55042200
Found NAND chip on Chip Select 0, chipSize=128MB, usable size=128MB, base=0x
brcmnand_scan: B4 nand_select = 40000101
brcmnand_scan: After nand_select = 40000101
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 2.0 NAND flash size 128MB @18000000
mtd->oobsize=64, mtd->eccOobSize=16
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
brcmnand_default_bbt: bbt_td = bbt_main_descr
Bad block table not found for chip 0
Bad block table not found for chip 0
Scanning device for bad blocks, options=00004000
Bad eraseblock 324 at 0x02880000
brcmnand_write_bbt: write_retry: startblock=3ff, dir=-1, td->maxblocks=8, skip=0
brcmnand_write_bbt: write_retry: startblock=3ff, dir=-1, td->maxblocks=8, skip=0
brcmnandCET: Did not find CET, recreating
brcmnandCET: Status -> Deferred
numchips=1, size=8000000
Creating 7 MTD partitions on "bcm7xxx-nand.0":
0x0000000000000000-0x0000000007400000 : "rootfs"
0x0000000007400000-0x0000000007800000 : "kernel"
0x0000000007800000-0x0000000007c00000 : "boot"
0x0000000007c00000-0x0000000007d00000 : "cfe"
0x0000000007d00000-0x0000000007d80000 : "mac"
0x0000000007d80000-0x0000000007e00000 : "env"
0x0000000007e00000-0x0000000007f00000 : "nvm"
usbmon: debugfs is not available
ehci_hcd_brcm_init: Initializing 2 EHCI controller(s)
brcm-pm: enabling power to USB block
10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-0)
drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
- USB h/w setup mode <B>
- USB power enable set for active HIGH mode
brcm-ehci brcm-ehci.0: BRCM EHCI
brcm-ehci brcm-ehci.0: new USB bus registered, assigned bus number 1
brcm-ehci brcm-ehci.0: irq 62, io mem 0x10480300
brcm-ehci brcm-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-1)
drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
brcm-ehci-1 brcm-ehci-1.1: BRCM EHCI
brcm-ehci-1 brcm-ehci-1.1: new USB bus registered, assigned bus number 2
brcm-ehci-1 brcm-ehci-1.1: irq 63, io mem 0x10480500
brcm-ehci-1 brcm-ehci-1.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ohci_hcd_brcm_init: Initializing 2 OHCI controller(s)
2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-0)
drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
- Resetting at b0480408
<-- brcm_start_hc
brcm-ohci-0 brcm-ohci-0.0: BRCM OHCI
brcm-ohci-0 brcm-ohci-0.0: new USB bus registered, assigned bus number 3
brcm-ohci-0 brcm-ohci-0.0: irq 64, io mem 0x10480400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-1)
drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
- Resetting at b0480608
<-- brcm_start_hc
brcm-ohci-1 brcm-ohci-1.1: BRCM OHCI
brcm-ohci-1 brcm-ohci-1.1: new USB bus registered, assigned bus number 4
brcm-ohci-1 brcm-ohci-1.1: irq 59, io mem 0x10480600
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
pegasus: v0.6.13 (2005/11/13), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new driver pegasus
drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
usbcore: registered new driver rtl8150
usbcore: registered new driver asix
usbcore: registered new driver cdc_ether
usbcore: registered new driver net1080
usbcore: registered new driver zaurus
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
VFS: Mounted root (jffs2 filesystem).
Freeing unused kernel memory: 120k freed
mount: mounting sysfs on /sys failed: Device or resource busy
Startting the hotplug events dispatcher
Synthesizing the initial hotplug events
Waiting for /dev to be fully populated
done
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
NTFS driver 2.1.27 [Flags: R/W MODULE].
procmk_init
dvb_bcm7325: module license 'Proprietary' taints kernel.
DVB: registering new adapter (vusolo)
bcm7335: hotplug_callback():
Hotplug - status.connected 0
CPU 0 Unable to handle kernel paging request at virtual address c0709a90, epc == c0709a90, ra == 8004dedc
Oops[#1]:
Cpu 0
$ 0 : 00000000 00000006 c0709a90 00010000
$ 4 : 0000000d c0b38824 86ae9cc8 853d31a1
$ 8 : 11008400 1000001f 00000068 0000002e
$12 : 00000020 0000004c 00000005 00000000
$16 : 853d0700 00000000 0000000d 00000001
$20 : 86ae9cc8 00000000 fffbffff 00000001
$24 : 00000000 fffffff9
$28 : 86ae8000 86ae9c20 00000000 8004dedc
Hi : 00000003
Lo : 5afe5358
epc : c0709a90 0xc0709a90 Tainted: P
ra : 8004dedc handle_IRQ_event+0x70/0xcc
Status: 11008002 KERNEL EXL
Cause : 10800008
BadVA : c0709a90
PrId : 0101954c
Modules linked in: dvb_core procmk snd_pcm snd_timer snd_page_alloc snd soundcor e firmware_class i2c_core evdev input ntfs vfat fat sr_mod cdrom usb_storage cif s nls_base isofs
Process udevd (pid: 53, threadinfo=86ae8000, task=86a6b178)
Stack : 8123df80 800b62ec 810c8320 86ae9c48 00000000 802cd680 0000000d 853d0700
86ae9cc8 00040000 80300000 8004e004 8123df80 800bb3d4 86ae9ce8 8031d5ec
0000000e 00000021 00000001 00000000 00000000 00001000 86ae9cc8 80006374
00000000 866c1098 86ae9ce0 86ae9e98 81233f00 80003d2c 802f2080 800704c4
86b5cd24 00000000 867f0f80 802f36cc 802f36e0 80268118 000000cd 802f36c8
...
Call Trace:
[<800b62ec>] proc_get_inode+0x27c/0x2b4
[<8004e004>] __do_IRQ+0xcc/0x158
[<800bb3d4>] proc_lookup+0x94/0xe0
[<80006374>] do_IRQ+0x1c/0x34
[<80003d2c>] brcm_mips_int2_dispatch+0xac/0x168
[<800704c4>] shmem_truncate+0x24/0x30
[<800048f4>] ret_from_irq+0x0/0x10
[<8008ea88>] __link_path_walk+0x1048/0x15b0
[<800bea00>] show_stat+0x1204/0x16e0
[<800a3900>] seq_printf+0xc/0x90
[<800bea00>] show_stat+0x1204/0x16e0
[<800a3d88>] seq_read+0x90/0x3cc
[<80079960>] vfs_read+0xb8/0x18c
[<80079b18>] sys_read+0x50/0x90
[<8000fbe4>] stack_done+0x20/0x3c
Code: (Bad address in epc)
Kernel panic - not syncing: Fatal exception in interrupt
<0>Rebooting in 180 seconds..